1763-L16BWA Allen-Bradley

Product Dimensions：

• Substitution of components may impair suitability for Class I, Division 2.

• Do not replace components or disconnect equipment unless power has been 

switched off.

• Do not connect or disconnect components unless power has been switched off.

• This product must be installed in an enclosure. All cables connected to the 

product must remain in the enclosure or be protected by conduit or other means.

• All wiring must comply with N.E.C. article 501-10(b).

• The interior of the enclosure must be accessible only by the use of a tool.

• For applicable equipment (for example, relay modules), exposure to some 

chemicals may degrade the sealing properties of the materials used in these 

devices:

– Relays, epoxy

It is recommended that you periodically inspect these devices for any degradation 

of properties and replace the module if degradation is found.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous 

locations only. The following WARNING statement applies to use in hazardous locations.

The 4 high-speed inputs (inputs 0 through 3) can be used for pulse latching or higher speed counting. Refer to Input 

Specifications on page 25 and the MicroLogix 1100 Instruction Set Reference Manual, publication 1763-RM001, for more 

information.

MicroLogix 1100 controllers are suitable for use in an industrial environment when installed 

in accordance with these instructions. Specifically, this equipment is intended for use in clean, 

dry environments (Pollution degree 2(1)) and with circuits not exceeding Over Voltage 

Category II(2) (IEC 60664-1).(3)

Install your controller using these installation instructions.

Do not remove the protective debris strip until after the controller and all other equipment 

in the panel near the controller are mounted and wiring is complete. Once wiring is 

complete, remove protective debris strip. Failure to remove strip before operating can 

cause overheating.

Electrostatic discharge can damage semiconductor devices inside the controller. Do not 

touch the connector pins or other sensitive areas.

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a 

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are 

controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

We have the same series of models in stock.  If you don't find the model you need, please contact us and we will provide you with an official quotation！

Allen-Bradley 440G-TZS21UPRH

Allen-Bradley 700-HLS1U2

Allen-Bradley 1440-SDM02-01RA

Allen-Bradley 1492-IFM40F-3

Allen-Bradley 1746-A10

Allen-Bradley 1746-NI4

Allen-Bradley 1746-NI8

Allen-Bradley 1747-L541

Allen-Bradley 1747-L552

Allen-Bradley 1756-A4

Allen-Bradley 1756-A10

Allen-Bradley 1756-A13

Allen-Bradley 1756-DHRI0C

Allen-Bradley 1756-DNB/A

Allen-Bradley 1756-EN2T

Allen-Bradley 1756-EN2TR

Allen-Bradley 1756-ENBT

Allen-Bradley 1756-IA16I

Allen-Bradley 1756-IB16

Allen-Bradley 1756-IF16

Allen-Bradley 1756-IR6I

Allen-Bradley 1756-L7SP

Allen-Bradley 1756-L71 

Allen-Bradley 1756-L71S

Allen-Bradley 1756-L81ES

Colour：new                                  Warranty: 12 months

Lead Time：3-day working day     Price: Please contact us  

Shipping Port: Xiamen, China        Payment:T/T

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service